# AGA error codes, decoded

> 31 fault and indicator codes across AGA control platforms.

## AGA TEK / Tekelek PCB fault codes

- [002 — Com WD Fault (communication watchdog)](https://aga.repair/aga-error-code-002)
- [003 — Com WD Fault (communication watchdog)](https://aga.repair/aga-error-code-003)
- [004 — Not used](https://aga.repair/aga-error-code-004)
- [005 — Not used](https://aga.repair/aga-error-code-005)
- [006 — WD WDT Fault (watchdog timer)](https://aga.repair/aga-error-code-006)
- [007 — TC Ref Fault — the user panel PCB is unable to process thermocouple measurements](https://aga.repair/aga-error-code-007)
- [010-014 — Full power time out — the cooking zone is taking too long to reach its expected temperature. This is a safety feature, not necessarily a component failure.](https://aga.repair/aga-error-code-010-014)
- [020-024 — Thermocouple differential — the two thermocouples in a zone disagree](https://aga.repair/aga-error-code-020-024)
- [060-100 — Thermocouple open circuit](https://aga.repair/aga-error-code-060-100)
- [110-116 — Relay short circuit](https://aga.repair/aga-error-code-110-116)
- [120-124 — Cooking zone overheat error](https://aga.repair/aga-error-code-120-124)
- [130-136 — Triac fault](https://aga.repair/aga-error-code-130-136)
- [139 — User panel overheat — excessive temperatures recorded at the control panel](https://aga.repair/aga-error-code-139)
- [140 — Configuration key fault](https://aga.repair/aga-error-code-140)
- [150-156 — Relay open circuit](https://aga.repair/aga-error-code-150-156)
- [159 — RF fault — receiver not communicating with the PCB](https://aga.repair/aga-error-code-159)

## AGA dishwasher indicators

- [0:01 after 3-2-1 countdown — Program cancellation in progress; drains for about 2 minutes then beeps](https://aga.repair/aga-error-code-cancellation-countdown)
- [F1 — Half Load function](https://aga.repair/aga-error-code-f1)
- [F2 — Sanitize function (raises final rinse temperature to NSF/ANSI 184)](https://aga.repair/aga-error-code-f2)
- [F3 — HighGloss function (3 Series only)](https://aga.repair/aga-error-code-f3)
- [F4 — Intense Wash function (3 Series only)](https://aga.repair/aga-error-code-f4)
- [S — Displayed at the end of a successful sanitization cycle](https://aga.repair/aga-error-code-s-indicator)
- [S:0 / S:1 / S:2 — Sound volume setting (off / medium / high). Factory default S:2.](https://aga.repair/aga-error-code-sound-volume-setting)

## AGA customer touch-panel / handset display codes

- [CE — No response from main controller](https://aga.repair/aga-error-code-ce)
- [FE — Touch panel microcontroller unresponsive or malfunctioned](https://aga.repair/aga-error-code-fe)
- [VE — Main controller firmware version incompatible](https://aga.repair/aga-error-code-ve)

## AGA induction hob / range error codes

- [E2 — The electronic unit is too hot](https://aga.repair/aga-error-code-e2)
- [E6 — Cookware / load fault (AGA ERA)](https://aga.repair/aga-error-code-e6)
- [Er + number — Internal technical fault that cannot be rectified by the user](https://aga.repair/aga-error-code-er-plus-number)
- [(no display operation) — Over-voltage or loss of supply voltage to the range](https://aga.repair/aga-error-code-no-display-operation)
- [U400 — The range has been incorrectly connected (supply wiring fault)](https://aga.repair/aga-error-code-u400)

---

## Book a repair

- Call or text: 206-427-7323 (Mon–Sun 8:00AM–8:00PM, Pacific Time)
- Book online: https://aga.repair/contact/
- Email: service@aga.repair
- Service at your home across the Seattle–Tacoma metro, WA. Diagnostic fee applies toward your repair.

Independent service company — not affiliated with or authorized by AGA / AGA Rangemaster (Middleby). We repair out-of-warranty AGA appliances.